Vitals360®
The Vitals360®, This FDA cleared Six Key Vital Signs Monitor measures Heart Rate, Blood Oxygen Saturation, Temperature, Blood Pressure, ECG Heart Rhythms, and Glucose (Not available in the USA).
HOW TO USE IT
In just three easy steps, you can able to take reading from Vital 360
1.Connect to Device
1.Patient has to turn on device & make sure device is connected to Internet
2. Click on Switch Modes and select Test and share mode
2.Measure Vitals
1.click on BPM Tile on Vital 360 device
2. Select patient Positions
3. Select the Hand to Measure Vital
3.Sync Readings
-Click on save to sync the latest readings into callcare 24 app.
– Click on retest to take a different BP/pulse readings.
FAQ's
Vitals360® is a comprehensive health monitoring device that measures six key vital signs: heart rate, blood oxygen saturation, temperature, blood pressure, ECG heart rhythms, and glucose (not available in the USA).
Yes, Vitals360® is FDA-cleared for heart rate, blood oxygen saturation, ECG heart rhythms, and temperature.
The frequency of use depends on your individual needs and medical advice. Consult with your healthcare provider for specific recommendations.
The blood pressure measurement on Vitals360® is highly accurate and comparable to traditional blood pressure cuffs.
Yes, Vitals360® can monitor glucose levels, but this feature is not available in the USA.
The battery life of Vitals360® varies depending on usage and settings. Please refer to the user manual for specific information.
Yes, Vitals360® can be connected to your smartphone via Bluetooth to sync and analyze your data.
Ensure that both devices are within Bluetooth range and that Bluetooth is enabled on both devices. Try restarting both devices and checking for any software updates.
If you encounter any issues with Vitals360®, please contact customer support for assistance.
Troubleshooting
1. Device battery problem.
2. Internet connectivity.
1. Check the battery status of Vital 360 device.
2. Make sure to charge the device if the battery is low.
3. Switch off the device and Turn it on again.
4. Check the internet is properly connected through Wi-Fi / Cellular network.
5. Change the network mode and try to save the readings.
6. Retake the vitals from device and verify that they are displaying correctly.
1. Improper Cuff placement to hand.
2. Improper Selection of positions in vital 360 & not maintaining same positions while measuring BP
1. Check the cuff is placed correctly to selected hand.
2. Keep the cuff properly to hand.
3. Check the device is placed correctly while measuring the BP
4. Verify the vital data after measuring and try to retake the readings if the data is not accurate.
1. Improper placement of IR sensor to body
2. Improper accuracy because of dust or dirt in IR sensor
1. Check the device is connected to proper internet
2. Make sure you’re holding the Vital 360 at the correct distance
3. Clean the infrared sensor with a soft cloth, as dust or dirt can impact accuracy.
4. Allow a few seconds between measurements to reset the sensor.
5. Wait or hold the device until the timer completes
Indications
- If Display or measurement values not working correctly
- If Blood Pressure readings are not getting correctly
- If Temperature readings are not getting correctly
Causes
- Device battery problem.
- Internet connectivity.
- Improper Cuff placement to hand.
- Improper Selection of positions in vital 360 & not maintaining same positions while measuring BP
- Improper placement of IR sensor to body
- Improper accuracy because of dust or dirt in IR sensor
Solutions
- Check the battery status of Vital 360 device.
- Make sure to charge the device if the battery is low.
- Switch off the device and Turn it on again.
- Check the internet is properly connected through Wi-Fi / Cellular network.
- Change the network mode and try to save the readings.
- Retake the vitals from device and verify that they are displaying correctly.
- Check the cuff is placed correctly to selected hand.
- Keep the cuff properly to hand.
- Check the device is placed correctly while measuring the BP
- Verify the vital data after measuring and try to retake the readings if the data is not accurate.
- Check the device is connected to proper internet
- Make sure you’re holding the Vital 360 at the correct distance
- Clean the infrared sensor with a soft cloth, as dust or dirt can impact accuracy.
- Allow a few seconds between measurements to reset the sensor.
- Wait or hold the device until the timer completes
Contact Us
USA
- 831 N Tatnall St., STE M #134 Wilmington, DE – 19801
- +1 614 615 1507
- info@callcare24.com
- 4200 Research Forest Dr, The Woodlands, TX - 77381
- sales@callcare24.com
INDIA
- Suite 303, 3rd Floor, Trade Fair Office Building, Hitex Exhibition Center, Hyderabad, Telangana - 500084
- +91 62 62 95 72 72
- info@callcare24.com
- sales@callcare24.com
SAUDI ARABIA
- 7730, King Saud Al Sulimaniyah District, Mazya Tower 3, 12621 Riyadh, KSA.
- +966 11 505 1894
- info@callcare24.com
- sales@callcare24.com
